Distributed Replicated Storage Across Four Storage Nodes With GlusterFS On Mandriva 2010.0

This tutorial shows how to combine four single storage servers (running Mandriva 2010.0) to a distributed replicated storage with GlusterFS. Nodes 1 and 2 (replication1) as well as 3 and 4 (replication2) will mirror each other, and replication1 and replication2 will be combined to one larger storage server (distribution). Basically, this is RAID10 over network. If you lose one server from replication1 and one from replication2, the distributed volume continues to work. The client system (Mandriva 2010.0 as well) will be able to access the storage as if it was a local filesystem. GlusterFS is a clustered file-system capable of scaling to several peta-bytes. It aggregates various storage bricks over Infiniband RDMA or TCP/IP interconnect into one large parallel network file system. Storage bricks can be made of any commodity hardware such as x86_64 servers with SATA-II RAID and Infiniband HBA.

I do not issue any guarantee that this will work for you!


1 Preliminary Note

In this tutorial I use five systems, four servers and a client:

  • server1.example.com: IP address (server)
  • server2.example.com: IP address (server)
  • server3.example.com: IP address (server)
  • server4.example.com: IP address (server)
  • client1.example.com: IP address (client)

All five systems should be able to resolve the other systems' hostnames. If this cannot be done through DNS, you should edit the /etc/hosts file so that it looks as follows on all five systems:

vi /etc/hosts       localhost.localdomain   localhost   server1.example.com     server1   server2.example.com     server2   server3.example.com     server3   server4.example.com     server4   client1.example.com     client1

(It is also possible to use IP addresses instead of hostnames in the following setup. If you prefer to use IP addresses, you don't have to care about whether the hostnames can be resolved or not.)


2 Setting Up The GlusterFS Servers


GlusterFS is available as a package for Mandriva 2010.0, therefore we can install it as follows:

urpmi glusterfs-server

The command

glusterfs --version

should now show the GlusterFS version that you've just installed (2.0.6 in this case):

[root@server1 administrator]# glusterfs --version
glusterfs 2.0.6 built on Sep 20 2009 06:40:50
Repository revision: v2.0.6
Copyright (c) 2006-2009 Z RESEARCH Inc. <http://www.zresearch.com>
You may redistribute copies of GlusterFS under the terms of the GNU General Public License.
[root@server1 administrator]#

Next we create a few directories:

mkdir /data/
mkdir /data/export
mkdir /data/export-ns

Now we create the GlusterFS server configuration file /etc/glusterfs/glusterfsd.vol which defines which directory will be exported (/data/export) and what client is allowed to connect ( = client1.example.com):

vi /etc/glusterfs/glusterfsd.vol

volume posix
  type storage/posix
  option directory /data/export

volume locks
  type features/locks
  subvolumes posix

volume brick
  type performance/io-threads
  option thread-count 8
  subvolumes locks

volume server
  type protocol/server
  option transport-type tcp
  option auth.addr.brick.allow
  subvolumes brick

Please note that it is possible to use wildcards for the IP addresses (like 192.168.*) and that you can specify multiple IP addresses separated by comma (e.g.,

Afterwards we start the GlusterFS server:

/etc/init.d/glusterfsd restart

Share this page:

1 Comment(s)

Add comment



CAUTION: Gluster configuration has changed since this article was written. The Refer to the Gluster Information Wiki for the current steps+commands to configure Gluster.