ISPConfig3 Compled Install and within 5 Seconds, Server Went Dead???

Discussion in 'Installation/Configuration' started by ipvsinc, Dec 14, 2012.

  1. ipvsinc

    ipvsinc New Member

    Hi There,

    I'm baffled and could use some suggestions. I spent 3+ hours installing IPSConfig3 on Centos 6.2. It went perfect. At the end of the 7 page tutorial, it installed ISPConfig , noted Installation Completed. And within 5 seconds, the system went dead. I couldn't ping it... Nothing. I powered the system off, then powered it back on maintaining a ping to it... As soon as it was ping-able, I ssh'ed into it... and it went completely dead again within 5 seconds... ???? Since the system has a 16GB SATADOM drive which holds the OS / boot partitions and a 4 Terabyte RAID 5 on it,.. I figured that something may have happen like the disk filling up. I was able to check this and it was fine... But the system/ssh session went dead again. Another power off and power back on showed the same. The system came alive allowing me to login and within 5 seconds was unresponsive again.

    See the ouptut for the last part of the install... I'm completely baffled on where to go from here??? Any suggestions would be appreciated.

    I do have the entire ssh/console date during the install process if that would help.

    Thank you,


    Tim





    Please enter the following 'extra' attributes
    to be sent with your certificate request
    A challenge password []:
    An optional company name []:
    writing RSA key
    Configuring DBServer
    Installing ISPConfig crontab
    no crontab for root
    no crontab for getmail
    Restarting services ...
    Stopping mysqld: [ OK ]
    Starting mysqld: [ OK ]
    Shutting down postfix: [ OK ]
    Starting postfix: [ OK ]
    Stopping saslauthd: [FAILED]
    Starting saslauthd: [ OK ]
    Shutting down amavisd: Daemon [16405] terminated by SIGTERM
    [ OK ]
    amavisd stopped
    Starting amavisd: [ OK ]

    Stopping clamd.amavisd: [ OK ]
    Starting clamd.amavisd: [ OK ]
    Stopping Courier authentication services: authdaemond
    Starting Courier authentication services: authdaemond
    Stopping Courier-IMAP server: imap imap-ssl pop3 pop3-ssl
    Starting Courier-IMAP server: imap imap-ssl pop3 pop3-ssl
    Stopping Courier-IMAP server: imap imap-ssl pop3 pop3-ssl
    Starting Courier-IMAP server: imap imap-ssl pop3 pop3-ssl
    Stopping Courier-IMAP server: imap imap-ssl pop3 pop3-ssl
    Starting Courier-IMAP server: imap imap-ssl pop3 pop3-ssl
    Stopping Courier-IMAP server: imap imap-ssl pop3 pop3-ssl
    Starting Courier-IMAP server: imap imap-ssl pop3 pop3-ssl
    Stopping httpd: [ OK ]
    [Thu Dec 13 16:28:00 2012] [warn] NameVirtualHost *:80 has no VirtualHosts
    Starting httpd: [ OK ]
    Stopping pure-ftpd: [ OK ]
    Starting pure-ftpd: [ OK ]
    Installation completed.
    16:28:03-root@Web1:/tmp/ispconfig3_install/install#Write failed: Broken pipe
    16:30:12-tim@tim-ipvsinc-com:~#
     
  2. ipvsinc

    ipvsinc New Member

    More info that may help. I was able to boot and cat /var/log/messages. It seems that the system boots and freezes up each time after noting "Dec 13 19:07:04 web2 kernel: Bridge firewalling registered".

    See follows for /var/log/messages before the system freezes each time:

    Code:
    Dec 13 19:02:23 web2 kernel: igb 0000:04:00.1: Intel(R) Gigabit Ethernet Network Connection
    Dec 13 19:02:23 web2 kernel: igb 0000:04:00.1: eth1: (PCIe:5.0Gb/s:Width x4) 00:25:90:79:22:6f
    Dec 13 19:02:23 web2 kernel: igb 0000:04:00.1: eth1: PBA No: FFFFFF-0FF
    Dec 13 19:02:23 web2 kernel: igb 0000:04:00.1: Using MSI-X interrupts. 8 rx queue(s), 8 tx queue(s)
    Dec 13 19:02:23 web2 kernel: EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: 
    Dec 13 19:02:23 web2 kernel: EXT4-fs (dm-2): mounted filesystem with ordered data mode. Opts: 
    Dec 13 19:02:23 web2 kernel: Adding 35061752k swap on /dev/mapper/vg_web02-lv_swap.  Priority:-1 extents:1 across:35061752k 
    Dec 13 19:02:23 web2 kernel: NET: Registered protocol family 10
    Dec 13 19:02:23 web2 kernel: lo: Disabled Privacy Extensions
    Dec 13 19:02:23 web2 kernel: ADDRCONF(NETDEV_UP): eth0: link is not ready
    Dec 13 19:02:23 web2 kernel: igb: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
    Dec 13 19:02:23 web2 kernel: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
    Dec 13 19:02:23 web2 kernel: ADDRCONF(NETDEV_UP): eth1: link is not ready
    Dec 13 19:02:24 web2 cpuspeed: Enabling ondemand cpu frequency scaling governor
    Dec 13 19:02:24 web2 named[1969]: starting BIND 9.8.2rc1-RedHat-9.8.2-0.10.rc1.el6_3.6 -u named
    Dec 13 19:02:24 web2 named[1969]: built with '--build=x86_64-redhat-linux-gnu' '--host=x86_64-redhat-linux-gnu' '--target=x86_64-redhat-linux-gnu' '--program-prefix=' '--prefix=/usr' '--exec-prefix=/usr' '--bindir=/usr/bin' '--sbindir=/usr/sbin' '--sysconfdir=/etc' '--datadir=/usr/share' '--includedir=/usr/include' '--libdir=/usr/lib64' '--libexecdir=/usr/libexec' '--sharedstatedir=/var/lib' '--mandir=/usr/share/man' '--infodir=/usr/share/info' '--with-libtool' '--localstatedir=/var' '--enable-threads' '--enable-ipv6' '--with-pic' '--disable-static' '--disable-openssl-version-check' '--with-dlz-ldap=yes' '--with-dlz-postgres=yes' '--with-dlz-mysql=yes' '--with-dlz-filesystem=yes' '--with-gssapi=yes' '--disable-isc-spnego' '--with-docbook-xsl=/usr/share/sgml/docbook/xsl-stylesheets' '--enable-fixed-rrset' 'build_alias=x86_64-redhat-linux-gnu' 'host_alias=x86_64-redhat-linux-gnu' 'target_alias=x86_64-redhat-linux-gnu' 'CFLAGS= -O2 -g -pipe -Wall -Wp,-D_FORTIFY_SOURCE=2 -fexceptions -fstack-protector --param=ssp-buffer-size=4 -m64 -mtune=generic' 'CPPFLAGS= -DDIG_SIGCHASE'
    Dec 13 19:02:24 web2 named[1969]: ----------------------------------------------------
    Dec 13 19:02:24 web2 named[1969]: BIND 9 is maintained by Internet Systems Consortium,
    Dec 13 19:02:24 web2 named[1969]: Inc. (ISC), a non-profit 501(c)(3) public-benefit 
    Dec 13 19:02:24 web2 named[1969]: corporation.  Support and training for BIND 9 are 
    Dec 13 19:02:24 web2 named[1969]: available at https://www.isc.org/support
    Dec 13 19:02:24 web2 named[1969]: ----------------------------------------------------
    Dec 13 19:02:24 web2 named[1969]: adjusted limit on open files from 1024 to 1048576
    Dec 13 19:02:24 web2 named[1969]: found 12 CPUs, using 12 worker threads
    Dec 13 19:02:24 web2 named[1969]: using up to 4096 sockets
    Dec 13 19:02:24 web2 named[1969]: loading configuration from '/etc/named.conf'
    Dec 13 19:02:24 web2 named[1969]: using default UDP/IPv4 port range: [1024, 65535]
    Dec 13 19:02:24 web2 named[1969]: using default UDP/IPv6 port range: [1024, 65535]
    Dec 13 19:02:24 web2 named[1969]: listening on IPv6 interfaces, port 53
    Dec 13 19:02:24 web2 named[1969]: listening on IPv4 interface lo, 127.0.0.1#53
    Dec 13 19:02:24 web2 named[1969]: listening on IPv4 interface eth0, 199.73.54.172#53
    Dec 13 19:02:24 web2 named[1969]: generating session key for dynamic DNS
    Dec 13 19:02:24 web2 named[1969]: sizing zone task pool based on 1 zones
    Dec 13 19:02:24 web2 named[1969]: set up managed keys zone for view _default, file 'dynamic/managed-keys.bind'
    Dec 13 19:02:24 web2 named[1969]: Warning: 'empty-zones-enable/disable-empty-zone' not set: disabling RFC 1918 empty zones
    Dec 13 19:02:24 web2 named[1969]: automatic empty zone: 0.IN-ADDR.ARPA
    Dec 13 19:02:24 web2 named[1969]: automatic empty zone: 127.IN-ADDR.ARPA
    Dec 13 19:02:24 web2 named[1969]: automatic empty zone: 254.169.IN-ADDR.ARPA
    Dec 13 19:02:24 web2 named[1969]: automatic empty zone: 2.0.192.IN-ADDR.ARPA
    Dec 13 19:02:24 web2 named[1969]: automatic empty zone: 100.51.198.IN-ADDR.ARPA
    Dec 13 19:02:24 web2 named[1969]: automatic empty zone: 113.0.203.IN-ADDR.ARPA
    Dec 13 19:02:24 web2 named[1969]: automatic empty zone: 255.255.255.255.IN-ADDR.ARPA
    Dec 13 19:02:24 web2 named[1969]: automatic empty zone: 0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.IP6.ARPA
    Dec 13 19:02:24 web2 named[1969]: automatic empty zone: 1.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.IP6.ARPA
    Dec 13 19:02:24 web2 named[1969]: automatic empty zone: D.F.IP6.ARPA
    Dec 13 19:02:24 web2 named[1969]: automatic empty zone: 8.E.F.IP6.ARPA
    Dec 13 19:02:24 web2 named[1969]: automatic empty zone: 9.E.F.IP6.ARPA
    Dec 13 19:02:24 web2 named[1969]: automatic empty zone: A.E.F.IP6.ARPA
    Dec 13 19:02:24 web2 named[1969]: automatic empty zone: B.E.F.IP6.ARPA
    Dec 13 19:02:24 web2 named[1969]: automatic empty zone: 8.B.D.0.1.0.0.2.IP6.ARPA
    Dec 13 19:02:24 web2 named[1969]: command channel listening on 127.0.0.1#953
    Dec 13 19:02:24 web2 named[1969]: command channel listening on ::1#953
    Dec 13 19:02:24 web2 named[1969]: managed-keys-zone ./IN: loaded serial 0
    Dec 13 19:02:24 web2 named[1969]: running
    Dec 13 19:02:24 web2 rpc.statd[2018]: Version 1.2.3 starting
    Dec 13 19:02:24 web2 sm-notify[2019]: Version 1.2.3 starting
    Dec 13 19:02:24 web2 kernel: RPC: Registered udp transport module.
    Dec 13 19:02:24 web2 kernel: RPC: Registered tcp transport module.
    Dec 13 19:02:24 web2 kernel: RPC: Registered tcp NFSv4.1 backchannel transport module.
    Dec 13 19:02:25 web2 kdump: kexec: loaded kdump kernel
    Dec 13 19:02:25 web2 kdump: started up
    Dec 13 19:02:26 web2 acpid: starting up
    Dec 13 19:02:26 web2 acpid: 1 rule loaded
    Dec 13 19:02:26 web2 acpid: waiting for events: event logging is off
    Dec 13 19:02:26 web2 acpid: client connected from 2254[68:68]
    Dec 13 19:02:26 web2 acpid: 1 client rule loaded
    Dec 13 19:02:28 web2 automount[2274]: lookup_read_master: lookup(nisplus): couldn't locate nis+ table auto.master
    Dec 13 19:02:28 web2 ntpd[2301]: ntpd [email protected] Tue Nov 29 00:09:12 UTC 2011 (1)
    Dec 13 19:02:28 web2 ntpd[2302]: precision = 0.173 usec
    Dec 13 19:02:28 web2 ntpd[2302]: Listening on interface #0 wildcard, 0.0.0.0#123 Disabled
    Dec 13 19:02:28 web2 ntpd[2302]: Listening on interface #1 wildcard, ::#123 Disabled
    Dec 13 19:02:28 web2 ntpd[2302]: Listening on interface #2 lo, ::1#123 Enabled
    Dec 13 19:02:28 web2 ntpd[2302]: Listening on interface #3 eth0, fe80::225:90ff:fe79:226e#123 Enabled
    Dec 13 19:02:28 web2 ntpd[2302]: Listening on interface #4 lo, 127.0.0.1#123 Enabled
    Dec 13 19:02:28 web2 ntpd[2302]: Listening on interface #5 eth0, 199.73.54.172#123 Enabled
    Dec 13 19:02:28 web2 ntpd[2302]: Listening on routing socket on fd #22 for interface updates
    Dec 13 19:02:28 web2 ntpd[2302]: kernel time sync status 2040
    Dec 13 19:02:28 web2 ntpd[2302]: frequency initialized -30.342 PPM from /var/lib/ntp/drift
    Dec 13 19:02:36 web2 abrtd: Init complete, entering main loop
    Dec 13 19:02:37 web2 qpidd[2652]: 2012-12-13 19:02:37 notice Listening on TCP/TCP6 port 5672
    Dec 13 19:02:37 web2 qpidd[2652]: 2012-12-13 19:02:37 notice SSL plugin not enabled, you must set --ssl-cert-db to enable it.
    Dec 13 19:02:37 web2 qpidd[2652]: 2012-12-13 19:02:37 notice Broker running
    Dec 13 19:02:38 web2 kernel: ip_tables: (C) 2000-2006 Netfilter Core Team
    Dec 13 19:02:39 web2 abrt: detected unhandled Python exception in '/usr/lib/mailman/bin/mailmanctl'
    Dec 13 19:02:39 web2 abrtd: New client connected
    Dec 13 19:02:39 web2 abrt-server[2759]: Saved Python crash dump of pid 2754 to /var/spool/abrt/pyhook-2012-12-13-19:02:39-2754
    Dec 13 19:02:39 web2 abrtd: Directory 'pyhook-2012-12-13-19:02:39-2754' creation detected
    Dec 13 19:02:42 web2 kernel: Bridge firewalling registered
     

Share This Page