installing domu on linux dom0 using CentOS-5.3-i386-bin-DVD.iso

Discussion in 'Installation/Configuration' started by laksh, Oct 27, 2009.

  1. laksh

    laksh New Member

    need help
    I have the config file which i am installing the vm from CentOS-5.3-i386-bin-DVD.iso
    but when I starting up the vm using xm create -c vmdom1.xm
    the error comes up please see the error output below.
    my config file looks like this

    kernel= "/xen/xen-3.4.1/dist/install/boot/vmlinuz-2.6.18.8-xenU"
    memory = 128
    name = "mailserver"
    root = "/dev/sda2 ro xencons=tty"
    vif = [ 'type=ioemu, bridge=eth0' ]
    disk = ['file:/lakxen/suselinux/xenimg/CentOS-5.3-i386-bin-DVD.iso,hda:cdrom,r', 'file:/lakxen/suselinux/image/disk.img,sda,w', ]

    error output is:
    Using config file "./vmdom1.xm".
    Started domain mailserver (id=27)
    Linux version 2.6.18.8-xenU (root@fc224.calsoft) (gcc version 4.1.2 20080704 (Red Hat 4.1.2-44)) #1 SMP Fri Aug 28 04:53:04 IST 2009
    BIOS-provided physical RAM map:
    Xen: 0000000000000000 - 0000000008800000 (usable)
    0MB HIGHMEM available.
    136MB LOWMEM available.
    NX (Execute Disable) protection: active
    Allocating PCI resources starting at 10000000 (gap: 08800000:f7800000)
    Detected 1864.860 MHz processor.
    Built 1 zonelists. Total pages: 34816
    Kernel command line: root=/dev/sda2 ro xencons=tty
    Enabling fast FPU save and restore... done.
    Enabling unmasked SIMD FPU exception support... done.
    Initializing CPU#0
    PID hash table entries: 1024 (order: 10, 4096 bytes)
    Xen reported: 1864.803 MHz processor.
    Console: colour dummy device 80x25
    Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
    Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
    Software IO TLB disabled
    vmalloc area: c9000000-f53fe000, maxmem 2d7fe000
    Memory: 126404k/139264k available (1926k kernel code, 4600k reserved, 520k data, 140k init, 0k highmem)
    Checking if this processor honours the WP bit even in supervisor mode... Ok.
    Calibrating delay using timer specific routine.. 3731.06 BogoMIPS (lpj=18655341)
    Mount-cache hash table entries: 512
    CPU: L1 I cache: 32K, L1 D cache: 32K
    CPU: L2 cache: 2048K
    Checking 'hlt' instruction... OK.
    SMP alternatives: switching to UP code
    Freeing SMP alternatives: 16k freed
    Brought up 1 CPUs
    migration_cost=0
    NET: Registered protocol family 16
    Brought up 1 CPUs
    suspend: event channel 6
    xen_mem: Initialising balloon driver.
    NET: Registered protocol family 2
    IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
    TCP established hash table entries: 8192 (order: 4, 65536 bytes)
    TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
    TCP: Hash tables configured (established 8192 bind 4096)
    TCP reno registered
    Initializing Cryptographic API
    io scheduler noop registered
    io scheduler anticipatory registered (default)
    io scheduler deadline registered
    io scheduler cfq registered
    RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
    Xen virtual console successfully installed as tty1
    Event-channel device installed.
    netfront: Initialising virtual ethernet driver.
    i8042.c: No controller found.
    mice: PS/2 mouse device common for all mice
    TCP bic registered
    NET: Registered protocol family 1
    NET: Registered protocol family 17
    Using IPI No-Shortcut mode
    xen-vbd: registered block device major 3
    blkfront: hda: barriers enabled
    hda: unknown partition table
    vif vif-0: 2 parsing device/vif/0/mac
    xen-vbd: registered block device major 8
    blkfront: sda: barriers enabled
    sda: unknown partition table
     

Share This Page