The Perfect Server - Fedora 15 x86_64 [ISPConfig 2] - Page 2

Want to support HowtoForge? Become a subscriber!
 
Submitted by falko (Contact Author) (Forums) on Fri, 2011-06-03 13:46. ::

The details for the last two repositories should now be retrieved, and the checkboxes in front of them should be marked. Click on Next:

Now we must select the package groups we want to install. Select Editors, Text-based Internet, Development Libraries, Development Tools, DNS Name Server, FTP Server, Mail Server, MySQL Database, Server Configuration Tools, Web Server, Administration Tools, Base, Hardware Support, Java, System Tools (unselect all other package groups) and click on Next:

The installation begins. This will take a few minutes:

Finally, the installation is complete, and you can remove your DVD from the computer and reboot it:

After the reboot, log in as root.

I want to install ISPConfig at the end of this tutorial which comes with its own firewall. That's why I disable the default Fedora firewall now. Of course, you are free to leave it on and configure it to your needs (but then you shouldn't use any other firewall later on as it will most probably interfere with the Fedora firewall).

Run...

system-config-firewall

... and disable the firewall. Hit OK afterwards:

Confirm your choice by selecting Yes:

If you did not configure your network card during the installation (because you did not select the additional online repositories), you can do that now. Run...

system-config-network

... and go to Device configuration:

Select your network interface (as I mentioned earlier, Fedora 15 uses BIOS device names, so the network card should be named something like p3p1 - we will change that soon so that it's named eth0):

Then fill in your network details - disable DHCP and fill in a static IP address, a netmask, and your gateway, then hit Ok:

Next select Save:

You can also specify additional nameservers. Select DNS configuration:

Now you can fill in additional nameservers and hit Ok:

Hit Save&Quit afterwards:

You should run

ifconfig

now to check if the installer got your IP address right:

[root@server1 ~]# ifconfig
lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:2 errors:0 dropped:0 overruns:0 frame:0
          TX packets:2 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:100 (100.0 b)  TX bytes:100 (100.0 b)

p3p1      Link encap:Ethernet  HWaddr 00:0C:29:15:60:FA
          inet addr:192.168.0.100  Bcast:192.168.0.255  Mask:255.255.255.0
          inet6 addr: fe80::20c:29ff:fe15:60fa/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:40 errors:0 dropped:0 overruns:0 frame:0
          TX packets:62 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:4678 (4.5 KiB)  TX bytes:10308 (10.0 KiB)

[root@server1 ~]#

Check your /etc/resolv.conf if it lists all nameservers that you've previously configured:

cat /etc/resolv.conf

If nameservers are missing, run

system-config-network

and add the missing nameservers again.

Now, on to the configuration...


Please do not use the comment function to ask for help! If you need help, please use our forum.
Comments will be published after administrator approval.
Submitted by roygrubb (not registered) on Mon, 2011-06-13 08:53.

On page 2 it says "After the reboot, log in as root." but Fedora 15 doesn't permit this.

 Roy