#1  
Old 18th December 2009, 05:56
kwickcut kwickcut is offline
Senior Member
 
Join Date: Nov 2005
Location: nj usa
Posts: 223
Thanks: 14
Thanked 11 Times in 10 Posts
Default add vsftpd to ispconfig

i have a ubuntu 9.10 server running ispcongis 2 and hosting 3 sites...useing proftpd.


problem is very slow transfer rates. i am getting complaints of speeds of 700k. i have read that vsftpd is way faster then prodtpd..


now i have add these lines to the config file in /etc/proftpd/proftpd.conf
Code:
#UseReverseDNS Toggle rDNS lookups
UseReverseDNS off
#IdentLookups Toggle ident lookups
IdentLookups off



<Global> 
IdentLookups off 
</Global>
this made no difference in the speeds

is there something else i could do to increase the speeds?

next question.

is vsftpd supported on ispconfig2 and is there a way to add vsftpd without having to reinstall ispconfig 2


thanks


kwick
Reply With Quote
Sponsored Links
  #2  
Old 18th December 2009, 21:36
kwickcut kwickcut is offline
Senior Member
 
Join Date: Nov 2005
Location: nj usa
Posts: 223
Thanks: 14
Thanked 11 Times in 10 Posts
Default

i have read that i can install vsftp just need to know how to configure it so it can be seen in ispconfig and not see proftpd



thanks



kwick
Reply With Quote
  #3  
Old 19th December 2009, 16:16
falko falko is offline
Super Moderator
 
Join Date: Apr 2005
Location: Lneburg, Germany
Posts: 41,701
Thanks: 1,900
Thanked 2,740 Times in 2,575 Posts
Default

Install vsftpd, and then post your /etc/vsftpd.conf here - I will help you to make the necessary changes.
__________________
Falko
--
Download the ISPConfig 3 Manual! | Check out the ISPConfig 3 Billing Module!

FB: http://www.facebook.com/howtoforge

nginx-Webhosting: Timme Hosting | Follow me on:
Reply With Quote
  #4  
Old 19th December 2009, 23:13
kwickcut kwickcut is offline
Senior Member
 
Join Date: Nov 2005
Location: nj usa
Posts: 223
Thanks: 14
Thanked 11 Times in 10 Posts
Default

thanks

Code:
write_enable=YES
#
# The default compiled in settings are fairly paranoid. This sample file
# loosens things up a bit, to make the ftp daemon more usable.
# Please see vsftpd.conf.5 for all compiled in defaults.
#
# READ THIS: This example file is NOT an exhaustive list of vsftpd options.
# Please read the vsftpd.conf.5 manual page to get a full idea of vsftpd's
# capabilities.
#
#
# Run standalone?  vsftpd can run either from an inetd or as a standalone
# daemon started from an initscript.
listen=YES
#
# Run standalone with IPv6?
# Like the listen parameter, except vsftpd will listen on an IPv6 socket
# instead of an IPv4 one. This parameter and the listen parameter are mutually
# exclusive.
#listen_ipv6=YES
#
# Allow anonymous FTP? (Beware - allowed by default if you comment this out).
anonymous_enable=YES
#
# Uncomment this to allow local users to log in.
local_enable=YES
#
# Uncomment this to enable any form of FTP write command.
#write_enable=YES
#
# Default umask for local users is 077. You may wish to change this to 022,
# if your users expect that (022 is used by most other ftpd's)
#local_umask=022
#
# Uncomment this to allow the anonymous FTP user to upload files. This only
# has an effect if the above global write enable is activated. Also, you will
# obviously need to create a directory writable by the FTP user.
#anon_upload_enable=YES
#
# Uncomment this if you want the anonymous FTP user to be able to create
# new directories.
#anon_mkdir_write_enable=YES
#
# Activate directory messages - messages given to remote users when they
# go into a certain directory.
dirmessage_enable=YES
#
# If enabled, vsftpd will display directory listings with the time
# in  your  local  time  zone.  The default is to display GMT. The
# times returned by the MDTM FTP command are also affected by this
# option.
use_localtime=YES
#
# Activate logging of uploads/downloads.
xferlog_enable=YES
#
# Make sure PORT transfer connections originate from port 20 (ftp-data).
connect_from_port_20=YES
#
# If you want, you can arrange for uploaded anonymous files to be owned by
# a different user. Note! Using "root" for uploaded files is not
# recommended!
#chown_uploads=YES
#chown_username=whoever
#
# You may override where the log file goes if you like. The default is shown
# below.
#xferlog_file=/var/log/vsftpd.log
#
# If you want, you can have your log file in standard ftpd xferlog format.
# Note that the default log file location is /var/log/xferlog in this case.
#xferlog_std_format=YES
#
# You may change the default value for timing out an idle session.
#idle_session_timeout=600
#
# You may change the default value for timing out a data connection.
#data_connection_timeout=120
#
# It is recommended that you define on your system a unique user which the
# ftp server can use as a totally isolated and unprivileged user.
#nopriv_user=ftpsecure
#
# Enable this and the server will recognise asynchronous ABOR requests. Not
# recommended for security (the code is non-trivial). Not enabling it,
# however, may confuse older FTP clients.
#async_abor_enable=YES
#
# By default the server will pretend to allow ASCII mode but in fact ignore
# the request. Turn on the below options to have the server actually do ASCII
# mangling on files when in ASCII mode.
# Beware that on some FTP servers, ASCII support allows a denial of service
# attack (DoS) via the command "SIZE /big/file" in ASCII mode. vsftpd
# predicted this attack and has always been safe, reporting the size of the
# raw file.
# ASCII mangling is a horrible feature of the protocol.
#ascii_upload_enable=YES
#ascii_download_enable=YES
#
# You may fully customise the login banner string:
#ftpd_banner=Welcome to blah FTP service.
#
# You may specify a file of disallowed anonymous e-mail addresses. Apparently
# useful for combatting certain DoS attacks.
#deny_email_enable=YES
# (default follows)
#banned_email_file=/etc/vsftpd.banned_emails
#
# You may restrict local users to their home directories.  See the FAQ for
# the possible risks in this before using chroot_local_user or
# chroot_list_enable below.
#chroot_local_user=YES
#
# You may specify an explicit list of local users to chroot() to their home
# directory. If chroot_local_user is YES, then this list becomes a list of
# users to NOT chroot().
chroot_local_user=YES
#chroot_list_enable=YES
# (default follows)
#chroot_list_file=/etc/vsftpd.chroot_list
#
# You may activate the "-R" option to the builtin ls. This is disabled by
# default to avoid remote users being able to cause excessive I/O on large
# sites. However, some broken FTP clients such as "ncftp" and "mirror" assume
# the presence of the "-R" option, so there is a strong case for enabling it.
#ls_recurse_enable=YES
#
#
# Debian customization
#
# Some of vsftpd's settings don't fit the Debian filesystem layout by
# default.  These settings are more Debian-friendly.
#
# This option should be the name of a directory which is empty.  Also, the
# directory should not be writable by the ftp user. This directory is used
# as a secure chroot() jail at times vsftpd does not require filesystem
# access.
secure_chroot_dir=/var/run/vsftpd/empty
#
# This string is the name of the PAM service vsftpd will use.
pam_service_name=vsftpd
#
# This option specifies the location of the RSA certificate to use for SSL
# encrypted connections.
rsa_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem


kwick
Reply With Quote
  #5  
Old 20th December 2009, 13:40
falko falko is offline
Super Moderator
 
Join Date: Apr 2005
Location: Lneburg, Germany
Posts: 41,701
Thanks: 1,900
Thanked 2,740 Times in 2,575 Posts
Default

Please enable the following options and restart vsftpd:

Code:
write_enable=YES
local_umask=022
__________________
Falko
--
Download the ISPConfig 3 Manual! | Check out the ISPConfig 3 Billing Module!

FB: http://www.facebook.com/howtoforge

nginx-Webhosting: Timme Hosting | Follow me on:
Reply With Quote
  #6  
Old 20th December 2009, 17:04
kwickcut kwickcut is offline
Senior Member
 
Join Date: Nov 2005
Location: nj usa
Posts: 223
Thanks: 14
Thanked 11 Times in 10 Posts
 
Default

thank you very much for the help



kwick
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
ISPConfig 3.0.0.4 Beta Released till General 54 4th March 2009 09:55
ISPConfig 3.0.0.6 Beta released till General 38 21st September 2008 19:15
ISPConfig 3.0.0.5 Beta Released till General 77 23rd July 2008 12:14
adding users / ispconfig wont add! help! mikeonline General 4 6th May 2008 22:59
Howto prevent that ISPconfig add unnecessary domain xneptuno Installation/Configuration 2 9th May 2007 15:21


All times are GMT +2. The time now is 20:51.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.