#1  
Old 9th May 2007, 13:29
josto josto is offline
Junior Member
 
Join Date: May 2007
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
Default Help with Bluetooth PAND

Hello,
I'm newbie with linux and I have a pc with on Debian that I use as little home server, I would like to set up on it a Bluetooth access point to surf the web with my Palm Tungsten T3.
I have tried to follow the HowTo that I found here http://www.howtoforge.com/bluetooth_pand_debian_etch but I didn't have success: I'm able to do the pairing but not to connect.
I have tried the command
Quote:
watch -n1 “ifconfig”
but I cant see bnep0 coming up
Quote:
eth0 Link encap:Ethernet HWaddr 00:02:44:6B:5E:B1
inet addr:192.168.1.37 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::202:44ff:fe6b:5eb1/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:107480 errors:0 dropped:0 overruns:0 frame:0
TX packets:132644 errors:15 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:52975165 (50.5 MiB) TX bytes:24314065 (23.1 MiB)
Interrupt:11 Base address:0x7400

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
I have tried the command
Quote:
hcidump
while trying to connect and this is the output
Quote:
HCI sniffer - Bluetooth packet analyzer ver 1.32
device: hci0 snap_len: 1028 filter: 0xffffffff
> HCI Event: Connect Request (0x04) plen 10
< HCI Command: Accept Connection Request (0x01|0x0009) plen 7
> HCI Event: Command Status (0x0f) plen 4
> HCI Event: Connect Complete (0x03) plen 11
< HCI Command: Read Remote Supported Features (0x01|0x001b) plen 2
> HCI Event: Command Status (0x0f) plen 4
< HCI Command: Write Link Policy Settings (0x02|0x000d) plen 4
> HCI Event: Read Remote Supported Features (0x0b) plen 11
> HCI Event: Command Complete (0x0e) plen 6
< HCI Command: Change Connection Packet Type (0x01|0x000f) plen 4
> HCI Event: Command Status (0x0f) plen 4
< HCI Command: Remote Name Request (0x01|0x0019) plen 10
> HCI Event: Connection Packet Type Changed (0x1d) plen 5
> HCI Event: Command Status (0x0f) plen 4
> HCI Event: Max Slots Change (0x1b) plen 3
> ACL data: handle 11 flags 0x02 dlen 12
L2CAP(s): Connect req: psm 1 scid 0x0040
< ACL data: handle 11 flags 0x02 dlen 16
L2CAP(s): Connect rsp: dcid 0x0040 scid 0x0040 result 0 status 0
Connection successful
> ACL data: handle 11 flags 0x02 dlen 12
L2CAP(s): Config req: dcid 0x0040 flags 0x00 clen 0
< ACL data: handle 11 flags 0x02 dlen 14
L2CAP(s): Config rsp: scid 0x0040 flags 0x00 result 0 clen 0
Success
< ACL data: handle 11 flags 0x02 dlen 12
L2CAP(s): Config req: dcid 0x0040 flags 0x00 clen 0
> ACL data: handle 11 flags 0x02 dlen 14
L2CAP(s): Config rsp: scid 0x0040 flags 0x00 result 0 clen 0
Success
> HCI Event: Remote Name Req Complete (0x07) plen 255
> ACL data: handle 11 flags 0x02 dlen 17
L2CAP(d): cid 0x0040 len 13 [psm 1]
SDP SS Req: tid 0x0 len 0x8
pat uuid-16 0x1102 (LAN)
max 1
cont 00
< ACL data: handle 11 flags 0x02 dlen 14
L2CAP(d): cid 0x0040 len 10 [psm 1]
SDP SS Rsp: tid 0x0 len 0x5
count 0
cont 00
> HCI Event: Number of Completed Packets (0x13) plen 5
> ACL data: handle 11 flags 0x02 dlen 21
L2CAP(d): cid 0x0040 len 17 [psm 1]
SDP SA Req: tid 0x1 len 0xc
handle 0x0
max 65535
aid(s) 0x0004 (ProtocolDescList)
cont 00
< ACL data: handle 11 flags 0x02 dlen 30
L2CAP(d): cid 0x0040 len 26 [psm 1]
SDP SA Rsp: tid 0x1 len 0x15
count 18
aid 0x0004 (ProtocolDescList)
< < uuid-16 0x0100 (L2CAP) uint 0x1 uint 0x1 > >
cont 00
> ACL data: handle 11 flags 0x02 dlen 21
L2CAP(d): cid 0x0040 len 17 [psm 1]
SDP SA Req: tid 0x2 len 0xc
handle 0x0
max 65535
aid(s) 0x0004 (ProtocolDescList)
cont 00
< ACL data: handle 11 flags 0x02 dlen 30
L2CAP(d): cid 0x0040 len 26 [psm 1]
SDP SA Rsp: tid 0x2 len 0x15
count 18
aid 0x0004 (ProtocolDescList)
< < uuid-16 0x0100 (L2CAP) uint 0x1 uint 0x1 > >
cont 00
> ACL data: handle 11 flags 0x02 dlen 12
L2CAP(s): Disconn req: dcid 0x0040 scid 0x0040
< ACL data: handle 11 flags 0x02 dlen 12
L2CAP(s): Disconn rsp: dcid 0x0040 scid 0x0040
> ACL data: handle 11 flags 0x02 dlen 12
L2CAP(s): Connect req: psm 1 scid 0x0040
< ACL data: handle 11 flags 0x02 dlen 16
L2CAP(s): Connect rsp: dcid 0x0040 scid 0x0040 result 0 status 0
Connection successful
> HCI Event: Number of Completed Packets (0x13) plen 5
> ACL data: handle 11 flags 0x02 dlen 12
L2CAP(s): Config req: dcid 0x0040 flags 0x00 clen 0
< ACL data: handle 11 flags 0x02 dlen 14
L2CAP(s): Config rsp: scid 0x0040 flags 0x00 result 0 clen 0
Success
< ACL data: handle 11 flags 0x02 dlen 12
L2CAP(s): Config req: dcid 0x0040 flags 0x00 clen 0
> ACL data: handle 11 flags 0x02 dlen 14
L2CAP(s): Config rsp: scid 0x0040 flags 0x00 result 0 clen 0
Success
> ACL data: handle 11 flags 0x02 dlen 17
L2CAP(d): cid 0x0040 len 13 [psm 1]
SDP SS Req: tid 0x3 len 0x8
pat uuid-16 0x1103 (DUN)
max 1
cont 00
< ACL data: handle 11 flags 0x02 dlen 14
L2CAP(d): cid 0x0040 len 10 [psm 1]
SDP SS Rsp: tid 0x3 len 0x5
count 0
cont 00
> ACL data: handle 11 flags 0x02 dlen 21
L2CAP(d): cid 0x0040 len 17 [psm 1]
SDP SA Req: tid 0x4 len 0xc
handle 0x0
max 65535
aid(s) 0x0004 (ProtocolDescList)
cont 00
< ACL data: handle 11 flags 0x02 dlen 30
L2CAP(d): cid 0x0040 len 26 [psm 1]
SDP SA Rsp: tid 0x4 len 0x15
count 18
aid 0x0004 (ProtocolDescList)
< < uuid-16 0x0100 (L2CAP) uint 0x1 uint 0x1 > >
cont 00
> HCI Event: Number of Completed Packets (0x13) plen 5
> ACL data: handle 11 flags 0x02 dlen 21
L2CAP(d): cid 0x0040 len 17 [psm 1]
SDP SA Req: tid 0x5 len 0xc
handle 0x0
max 65535
aid(s) 0x0004 (ProtocolDescList)
cont 00
< ACL data: handle 11 flags 0x02 dlen 30
L2CAP(d): cid 0x0040 len 26 [psm 1]
SDP SA Rsp: tid 0x5 len 0x15
count 18
aid 0x0004 (ProtocolDescList)
< < uuid-16 0x0100 (L2CAP) uint 0x1 uint 0x1 > >
cont 00
> ACL data: handle 11 flags 0x02 dlen 12
L2CAP(s): Disconn req: dcid 0x0040 scid 0x0040
< ACL data: handle 11 flags 0x02 dlen 12
L2CAP(s): Disconn rsp: dcid 0x0040 scid 0x0040
> ACL data: handle 11 flags 0x02 dlen 12
L2CAP(s): Connect req: psm 1 scid 0x0040
< ACL data: handle 11 flags 0x02 dlen 16
L2CAP(s): Connect rsp: dcid 0x0040 scid 0x0040 result 0 status 0
Connection successful
> ACL data: handle 11 flags 0x02 dlen 12
L2CAP(s): Config req: dcid 0x0040 flags 0x00 clen 0
< ACL data: handle 11 flags 0x02 dlen 14
L2CAP(s): Config rsp: scid 0x0040 flags 0x00 result 0 clen 0
Success
< ACL data: handle 11 flags 0x02 dlen 12
L2CAP(s): Config req: dcid 0x0040 flags 0x00 clen 0
> HCI Event: Number of Completed Packets (0x13) plen 5
> ACL data: handle 11 flags 0x02 dlen 14
L2CAP(s): Config rsp: scid 0x0040 flags 0x00 result 0 clen 0
Success
> ACL data: handle 11 flags 0x02 dlen 17
L2CAP(d): cid 0x0040 len 13 [psm 1]
SDP SS Req: tid 0x6 len 0x8
pat uuid-16 0x1101 (SP)
max 1
cont 00
< ACL data: handle 11 flags 0x02 dlen 14
L2CAP(d): cid 0x0040 len 10 [psm 1]
SDP SS Rsp: tid 0x6 len 0x5
count 0
cont 00
> ACL data: handle 11 flags 0x02 dlen 21
L2CAP(d): cid 0x0040 len 17 [psm 1]
SDP SA Req: tid 0x7 len 0xc
handle 0x0
max 65535
aid(s) 0x0004 (ProtocolDescList)
cont 00
< ACL data: handle 11 flags 0x02 dlen 30
L2CAP(d): cid 0x0040 len 26 [psm 1]
SDP SA Rsp: tid 0x7 len 0x15
count 18
aid 0x0004 (ProtocolDescList)
< < uuid-16 0x0100 (L2CAP) uint 0x1 uint 0x1 > >
cont 00
> ACL data: handle 11 flags 0x02 dlen 21
L2CAP(d): cid 0x0040 len 17 [psm 1]
SDP SA Req: tid 0x8 len 0xc
handle 0x0
max 65535
aid(s) 0x0004 (ProtocolDescList)
cont 00
< ACL data: handle 11 flags 0x02 dlen 30
L2CAP(d): cid 0x0040 len 26 [psm 1]
SDP SA Rsp: tid 0x8 len 0x15
count 18
aid 0x0004 (ProtocolDescList)
< < uuid-16 0x0100 (L2CAP) uint 0x1 uint 0x1 > >
cont 00
> HCI Event: Number of Completed Packets (0x13) plen 5
> ACL data: handle 11 flags 0x02 dlen 12
L2CAP(s): Disconn req: dcid 0x0040 scid 0x0040
< ACL data: handle 11 flags 0x02 dlen 12
L2CAP(s): Disconn rsp: dcid 0x0040 scid 0x0040
> HCI Event: Number of Completed Packets (0x13) plen 5
> HCI Event: Disconn Complete (0x05) plen 4
In addiction the debian server is not visible by other bluetooth devices, and I have to use the command
Quote:
hciconfig hci0 pisca
to make it visible.

Could someone please help me?

Thanks
Reply With Quote
Sponsored Links
  #2  
Old 7th August 2007, 20:53
hugolp hugolp is offline
Junior Member
 
Join Date: Aug 2007
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
 
Default

Hi

I am having problems as well. Its not working fine. I am guessing the problem is in the dhcp-server configuration, cause if I dont set my normal configuration as well as adding the bluetooth subnet it fails to start.

Also when I try to connect from the phone to the computer, it just stays there with the conecting screen. The interface is created but no internet acces.

Actually I am trying to get internet acces from my mobile phone using 3G to the computer. Is this posible using pand? or do I have to conect using the rcom mode?

Hugo
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +2. The time now is 08:26.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.