HowtoForge Forums | HowtoForge - Linux Howtos and Tutorials

unison config file on master:
Code:
# Roots of the synchronization

root = /var

root = ssh://81.XXX.XX.XXX//var/



# Paths to synchronize

path = www

path = vmail



# Some regexps specifying names and paths to ignore

#ignore = Path stats    ## ignores /var/www/stats

#ignore = Path stats/*  ## ignores /var/www/stats/*

#ignore = Path */stats  ## ignores /var/www/somedir/stats, but not /var/www/a/b/c/stats

#ignore = Name *stats   ## ignores all files/directories that end with "stats"

#ignore = Name stats*   ## ignores all files/directories that begin with "stats"

#ignore = Name *.tmp    ## ignores all files with the extension .tmp



#          When set to true, this flag causes the user interface to skip

#          asking for confirmations on non-conflicting changes. (More

#          precisely, when the user interface is done setting the

#          propagation direction for one entry and is about to move to the

#          next, it will skip over all non-conflicting entries and go

#          directly to the next conflict.)

auto=true



#          When this is set to true, the user interface will ask no

#          questions at all. Non-conflicting changes will be propagated;

#          conflicts will be skipped.

batch=true



#          !When this is set to true, Unison will request an extra

#          confirmation if it appears that the entire replica has been

#          deleted, before propagating the change. If the batch flag is

#          also set, synchronization will be aborted. When the path

#          preference is used, the same confirmation will be requested for

#          top-level paths. (At the moment, this flag only affects the

#          text user interface.) See also the mountpoint preference.

confirmbigdel=true



#          When this preference is set to true, Unison will use the

#          modification time and length of a file as a `pseudo inode

#          number' when scanning replicas for updates, instead of reading

#          the full contents of every file. Under Windows, this may cause

#          Unison to miss propagating an update if the modification time

#          and length of the file are both unchanged by the update.

#          However, Unison will never overwrite such an update with a

#          change from the other replica, since it always does a safe

#          check for updates just before propagating a change. Thus, it is

#          reasonable to use this switch under Windows most of the time

#          and occasionally run Unison once with fastcheck set to false,

#          if you are worried that Unison may have overlooked an update.

#          The default value of the preference is auto, which causes

#          Unison to use fast checking on Unix replicas (where it is safe)

#          and slow checking on Windows replicas. For backward

#          compatibility, yes, no, and default can be used in place of

#          true, false, and auto. See the section "Fast Checking" for more

#          information.

fastcheck=true



#          When this flag is set to true, the group attributes of the

#          files are synchronized. Whether the group names or the group

#          identifiers are synchronizeddepends on the preference numerids.

group=true



#          When this flag is set to true, the owner attributes of the

#          files are synchronized. Whether the owner names or the owner

#          identifiers are synchronizeddepends on the preference

#          extttnumerids.

owner=true



#          Including the preference -prefer root causes Unison always to

#          resolve conflicts in favor of root, rather than asking for

#          guidance from the user. (The syntax of root is the same as for

#          the root preference, plus the special values newer and older.)

#          This preference is overridden by the preferpartial preference.

#          This preference should be used only if you are sure you know

#          what you are doing!

prefer=newer



#          When this preference is set to true, the textual user interface

#          will print nothing at all, except in the case of errors.

#          Setting silent to true automatically sets the batch preference

#          to true.

silent=true



#          When this flag is set to true, file modification times (but not

#          directory modtimes) are propagated.

times=true
My emails are located at /var/vmail/domain/ on both servers.