HowtoForge Forums | HowtoForge - Linux Howtos and Tutorials

HowtoForge Forums | HowtoForge - Linux Howtos and Tutorials (http://www.howtoforge.com/forums/index.php)
-   Technical (http://www.howtoforge.com/forums/forumdisplay.php?f=8)
-   -   Can'r burn BD-R, DVD+R - OK. (http://www.howtoforge.com/forums/showthread.php?t=44802)

kaza 11th April 2010 06:18

Can'r burn BD-R, DVD+R - OK.
 
Hello,

I attempted to perform a backup onto a BD-R disk
and it seems not to be recognized while doing the same to
the DVD+R disk worked OK .
II attempted the burn with "CD/DVD Creator",
"B rasero Disk Burner" and "K3b". With all 3 it seems like the BD-R media
isn't recognized. In "K3b" the "Media info" shows what looks like a correct
data but when I go to "Settings -> Configure -> Devices" and look at the
"Writer drives" I see that the list of supported write formats goes only
as far as DVD+R(W) and DVD+R double layer, it doesn't include
BD-R format despite the fact that the burner itself is detected correctly:

Code:

Blockdevice: /dev/sr0
Generic device:
Vendor: HL-DT-ST
Description: BD-RE GGW-H20L

Please not that it uses the block device /dev/sr0 while I also
have a character device /dev/sg0:

Code:

<.../kaza>\ls -l /dev | grep cd
lrwxrwxrwx. 1 root root 3 2010-04-03 16:46 cdrom -> sr0
lrwxrwxrwx. 1 root root 3 2010-04-03 16:46 cdrw -> sr0
lrwxrwxrwx. 1 root root 3 2010-04-03 16:46 scd0 -> sr0
crw-rw----+ 1 root cdrom 21, 0 2010-04-03 16:46 sg0
brw-rw----+ 1 root cdrom 11, 0 2010-04-03 16:46 sr0

My bluray burner is connected to a SATA link and from "Googling"
about some error messages, it seems to me it should use
"Generic SCSI" through the /dev/sg0, am I right about it?
If yes, how can I instruct k3b what device to use? An attempt to
do "Add device" and typing "/dev/sg0" resulted in:
"Can't find additional device /dev/sg0".

When I start "k3b" (and ejecting and re-inserting the disk
in the middle) I get the following dumped into the terminal:

Code:

<.../kaza>k3b&
[1] 5423
<.../kaza>kbuildsycoca running...
(K3bDevice::HalConnection) initializing HAL >= 0.5
Mapping udi /org/freedesktop/Hal/devices/storage_model_BD_RE__GGW_H20L to device /dev/sr0
/dev/sr0 resolved to /dev/sr0
/dev/sr0 is block device (0)
/dev/sr0 seems to be cdrom
bus: 0, id: 0, lun: 0
(K3bDevice::Device) /dev/sr0: init()
(K3bDevice::Device) /dev/sr0 feature: CD Mastering
(K3bDevice::Device) /dev/sr0 feature: CD Track At Once
(K3bDevice::Device) /dev/sr0 feature: CD-RW Media Write Support
(K3bDevice::Device) /dev/sr0 feature: DVD Read (MMC5)
(K3bDevice::Device) /dev/sr0 feature: DVD+R
(K3bDevice::Device) /dev/sr0 feature: DVD+RW
(K3bDevice::Device) /dev/sr0 feature: DVD+R Double Layer
(K3bDevice::Device) /dev/sr0 feature: BD Read
(K3bDevice::Device) /dev/sr0 feature: BD Write
(K3bDevice::Device) /dev/sr0 feature: DVD-R/-RW Write
(K3bDevice::Device) /dev/sr0 feature: Rigid Restricted Overwrite
(K3bDevice::Device) /dev/sr0 feature: Layer Jump Recording
(K3bDevice::Device) /dev/sr0 feature: HD-DVD Read
(K3bDevice::Device) /dev/sr0 unknown profile: 2
(K3bDevice::Device) /dev/sr0: dataLen: 60
(K3bDevice::Device) /dev/sr0: checking for TAO
(K3bDevice::Device) /dev/sr0: checking for SAO
(K3bDevice::Device) /dev/sr0: checking for SAO_R96P
(K3bDevice::Device) /dev/sr0: checking for SAO_R96R
(K3bDevice::Device) /dev/sr0: checking for RAW_R16
(K3bDevice::Device) /dev/sr0: checking for RAW_R96P
(K3bDevice::Device) /dev/sr0: checking for RAW_R96R
(K3bDevice::Device) /dev/sr0: GET CONFIGURATION length det failed.
(K3bDevice::Device) /dev/sr0: GET CONFIGURATION length det failed.
(K3bDevice::Device) /dev/sr0: GET PERFORMANCE dataLen = 56
(K3bDevice::Device) /dev/sr0: GET PERFORMANCE successful with reported length: 52
(K3bDevice::Device) /dev/sr0: Number of supported write speeds via GET PERFORMANCE: 3
(K3bDevice::Device) /dev/sr0 : 26973 KB/s
(K3bDevice::Device) /dev/sr0 : 17982 KB/s
(K3bDevice::Device) /dev/sr0 : 8991 KB/s
(K3bDevice::DeviceManager) setting current write speed of device /dev/sr0 to 3324
/dev/sr0 resolved to /dev/sr0
(K3bDevice::DeviceManager) dev /dev/sr0 already found
(K3bDevice::DeviceManager) found config entry for devicetype: HL-DT-ST BD-RE GGW-H20L
(K3bDevice::Device) /dev/sr0: GET CONFIGURATION length det failed.
(K3bDevice::Device) /dev/sr0: GET CONFIGURATION length det failed.
Devices:
------------------------------
Blockdevice: /dev/sr0
Generic device:
Vendor: HL-DT-ST
Description: BD-RE GGW-H20L
Version: YL03
Write speed: 3324
Profiles: DVD-ROM, DVD-R Sequential, DVD-R Dual Layer Sequential, DVD-R Dual Layer Jump, DVD-RAM, DVD-RW Restricted Overwrite, DVD-RW Sequential, DVD+RW, DVD+R, DVD+R Dual Layer, CD-ROM, CD-R, CD-RW, HD DVD-ROM, BD-ROM, BD-R Sequential (SRM), BD-R Random (RRM), BD-RE
Read Cap: DVD-ROM, DVD-R, DVD-R Sequential, DVD-R Dual Layer, DVD-R Dual Layer Sequential, DVD-R Dual Layer Jump, DVD-RW, DVD-RW Restricted Overwrite, DVD-RW Sequential, DVD+RW, DVD+R, DVD+RW Dual Layer, DVD+R Dual Layer, CD-ROM, CD-R, CD-RW, HD DVD-ROM, HD DVD-R, BD-ROM, BD-R, BD-RE
Write Cap: DVD-R, DVD-R Sequential, DVD-R Dual Layer, DVD-R Dual Layer Sequential, DVD-R Dual Layer Jump, DVD-RW, DVD-RW Restricted Overwrite, DVD-RW Sequential, DVD+RW, DVD+R, DVD+R Dual Layer, CD-R, CD-RW, BD-R, BD-RE
Writing modes: SAO, TAO, RAW, SAO/R96P, SAO/R96R, RAW/R16, RAW/R96P, RAW/R96R, Restricted Overwrite, Layer Jump, Random Recording, Sequential Recording, Sequential Recording + POW
Reader aliases: /dev/sr0
------------------------------
DiskInfo:
Mediatype: BD-R Sequential (SRM)
Current Profile: BD-R Sequential (SRM)
Disk state: empty
Empty: 1
Rewritable: 0
Appendable: 0
Sessions: 0
Tracks: 0
Layers: 1
Capacity: 00:00:00 (LBA 0) (0 Bytes)
Remaining size: 00:00:00 (LBA 0) (0 Bytes)
Used Size: 00:00:00 (LBA 0) (0 Bytes)
(K3bDevice::Device) /dev/sr0: GET CONFIGURATION length det failed.
(K3bDevice::Device) /dev/sr0: GET PERFORMANCE dataLen = 56
(K3bDevice::Device) /dev/sr0: GET PERFORMANCE successful with reported length: 52
(K3bDevice::Device) /dev/sr0: Number of supported write speeds via GET PERFORMANCE: 3
(K3bDevice::Device) /dev/sr0 : 26973 KB/s
(K3bDevice::Device) /dev/sr0 : 17982 KB/s
(K3bDevice::Device) /dev/sr0 : 8991 KB/s
(K3bDevice::DeviceManager) request for empty device!
(K3bDevice::DeviceManager) request for empty device!
removing udi /org/freedesktop/Hal/devices/volume_empty_bd_r
(K3bDevice::Device) /dev/sr0: GET CONFIGURATION length det failed.
(K3bDevice::Device) /dev/sr0: GET CONFIGURATION length det failed.
DiskInfo:
Mediatype: BD-R Sequential (SRM)
Current Profile: BD-R Sequential (SRM)
Disk state: empty
Empty: 1
Rewritable: 0
Appendable: 0
Sessions: 0
Tracks: 0
Layers: 1
Capacity: 2715:25:17 (LBA 12219392) (25025314816 Bytes)
Remaining size: 2715:25:17 (LBA 12219392) (25025314816 Bytes)
Used Size: 00:00:00 (LBA 0) (0 Bytes)
adding udi /org/freedesktop/Hal/devices/volume_empty_bd_r
(K3bDevice::Device) /dev/sr0: GET CONFIGURATION length det failed.
(K3bDevice::Device) /dev/sr0: GET PERFORMANCE dataLen = 56
(K3bDevice::Device) /dev/sr0: GET PERFORMANCE successful with reported length: 52
(K3bDevice::Device) /dev/sr0: Number of supported write speeds via GET PERFORMANCE: 3
(K3bDevice::Device) /dev/sr0 : 26973 KB/s
(K3bDevice::Device) /dev/sr0 : 17982 KB/s
(K3bDevice::Device) /dev/sr0 : 8991 KB/s
(K3bDevice::DeviceManager) request for empty device!

[1] Done k3b
<.../kaza>ICE default IO error handler doing an exit(), pid = 5653, errno = 11

What doesn the message "GET CONFIGURATION length det failed."
means? I attempted to "Google" for this error message, got LOTS
of hits but couldn't find among them anything practical that looks
like a solution to my problem.

I'm running FC11, kernel: 2.6.29.4-167.hpfs.fc11.x86_64
with a GNOME desktop.
Any ideas as to what as to what am I doing wrong?
I also attempted to start "k3b" as a root with the same\results.

Thanks in advance for any help,
kaza.


All times are GMT +2. The time now is 19:20.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.