HowtoForge Forums | HowtoForge - Linux Howtos and Tutorials

HowtoForge Forums | HowtoForge - Linux Howtos and Tutorials (http://www.howtoforge.com/forums/index.php)
-   Installation/Configuration (http://www.howtoforge.com/forums/forumdisplay.php?f=16)
-   -   Client SSL send email issues only. (http://www.howtoforge.com/forums/showthread.php?t=24509)

NuttyGambler 25th June 2008 22:42

Client SSL send email issues only.
 
Have had this server up for a couple years. Gets email and sends mail fine inside the network.

Web clients can send and receive mal.

Remote clients can get email, but not send.

Fedora 6 (I know old but so far been able to upgrade apps so why rebuild)
Newest ISPConfig
Newest Postfix.

All done to Falkos Perfect setups.

Have read and read, but most in this seem to end up being client issues. But I have tried many different clients in every possible way.

If I don't require SSL
Jun 25 15:33:30 server04 postfix/smtpd[9011]: warning: 99-203-214-210.area2.spcsdns.net[99.203.214.210]: SASL LOGIN authentication failed: authentication failure
Jun 25 15:33:30 server04 postfix/smtpd[9011]: disconnect from 99-203-214-210.area2.spcsdns.net[99.203.214.210]
If I do.
Jun 25 15:36:59 server04 postfix/smtpd[9011]: setting up TLS connection from 99-203-214-210.area2.spcsdns.net[99.203.214.210]
Jun 25 15:37:02 server04 postfix/smtpd[9011]: TLS connection established from 99-203-214-210.area2.spcsdns.net[99.203.214.210]: SSLv3 with cipher RC4-MD5 (128/128 bits)
In either case the mail doesn't go out.

I'm out of ideas.

till 26th June 2008 10:58

Please make sure that you enabled smtp authentication in the client and that the client uses the same username and password for smtp auth that he uses for pop3.

If this wont work, please compare the email setup of your server with the perfect setup for fedora 6, it might be that you have a typo anywere in the initial setup as you post sounds that you never used smtp auth before on this server.

NuttyGambler 26th June 2008 14:41

Quote:

Originally Posted by till (Post 132826)
Please make sure that you enabled smtp authentication in the client and that the client uses the same username and password for smtp auth that he uses for pop3.

If this wont work, please compare the email setup of your server with the perfect setup for fedora 6, it might be that you have a typo anywere in the initial setup as you post sounds that you never used smtp auth before on this server.

Well I have been cut and pasting most everything, just changing server names, so unless there is is a typo in the instructions they are identical.

No, I used to have this working before I updated to a new server a couple years ago. Just given it is not critical to our operation I have ignored it, but now need to get it working for someone working remotely.

Looking at the above log clips. What should a working system say? In the one where I required auth, does it not look like the auth is working?

falko 26th June 2008 16:38

Is SELinux disabled?

NuttyGambler 27th June 2008 18:12

Quote:

Originally Posted by falko (Post 132880)
Is SELinux disabled?

Is according to the config file as in the setup page.

Is there a way to test that it is?

falko 27th June 2008 23:17

Quote:

Originally Posted by NuttyGambler (Post 133036)
Is there a way to test that it is?

Yes, run
Code:

sestatus


All times are GMT +2. The time now is 18:43.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.