HowtoForge Forums | HowtoForge - Linux Howtos and Tutorials

HowtoForge Forums | HowtoForge - Linux Howtos and Tutorials (http://www.howtoforge.com/forums/index.php)
-   Installation/Configuration (http://www.howtoforge.com/forums/forumdisplay.php?f=16)
-   -   Still errors with Openssl on Etch (http://www.howtoforge.com/forums/showthread.php?t=12957)

jake 27th May 2007 19:57

Still errors with Openssl on Etch
 
Hello,

First off, thank you for a great piece of software. I've been using ISPConfig for 6 months now, and I found a very easy to use! A great tool.

Recently i've tried to upgrade the installation to the latest version but there something went wrong. So i decided to reinstall my (virtual server). But whatever i try the install seems to go wrong everytime.

I've tried to change the line in compile_aps/compile as described in one of the other topics, but when i do that, i'm able to go to certifcate generation. But this generation takes forever. I've let it run for 24 hours, but it was still busy.
If i don't change the lines i've got the following error:

Here's some info from my system:
Code:

uname -a
Linux broomhilda.hyperactief.com 2.6.17.13-vs2.0.2.1-node-b02 #1 SMP Thu May 17 22:00:00 UTC 2007 x86_64 GNU/Linux

Running debian etch 4.0

I followed the perfect setup as closely as possible (due to having a vserver). I skipped the quota section partially and was unable to install bind9 (has been replaced by dnsutils?) so i installed bind. Perhaps a problem with the sources.list file?

The error:
Code:

gcc -DMONOLITH -I.. -I../include  -DOPENSSL_THREADS -D_REENTRANT -DDSO_DLFCN -DHAVE_DLFCN_H -m64 -DL_ENDIAN -DTERMIO -O3 -Wall -DMD32_REG_T=int -DMD5_ASM  -c -o s_server.o s_server.c
/tmp/ccI8c8VC.s: Assembler messages:
/tmp/ccI8c8VC.s:437: Error: Incorrect register `%rax' used with `l' suffix
/tmp/ccI8c8VC.s:445: Error: Incorrect register `%rbx' used with `l' suffix
/tmp/ccI8c8VC.s:465: Error: Incorrect register `%rdx' used with `l' suffix
/tmp/ccI8c8VC.s:466: Error: Incorrect register `%rbx' used with `l' suffix
make[1]: *** [s_server.o] Error 1
make[1]: Leaving directory `/root/install_ispconfig/compile_aps/openssl-0.9.8e/apps'
make: *** [build_apps] Error 1
ERROR: Could not make OpenSSL
rm: cannot remove `install_ispconfig/.nfs00000000025447870006afb9': Device or resource busy
rm: cannot remove `install_ispconfig/.nfs00000000025448550006afba': Device or resource busy
mv: cannot stat `binaries/aps.tar.gz': No such file or directory
mv: cannot stat `binaries/spamassassin.tar.gz': No such file or directory
mv: cannot stat `binaries/uudeview.tar.gz': No such file or directory
mv: cannot stat `binaries/clamav.tar.gz': No such file or directory
mv: cannot stat `binaries/cronolog': No such file or directory
mv: cannot stat `binaries/cronosplit': No such file or directory
mv: cannot stat `binaries/ispconfig_tcpserver': No such file or directory
mv: cannot stat `binaries/zip': No such file or directory
mv: cannot stat `binaries/unzip': No such file or directory
tar: spamassassin.tar.gz: Cannot open: No such file or directory
tar: Error is not recoverable: exiting now
tar: Child returned status 2
tar: Error exit delayed from previous errors
mv: cannot stat `spamassassin': No such file or directory
tar: uudeview.tar.gz: Cannot open: No such file or directory
tar: Error is not recoverable: exiting now
tar: Child returned status 2
tar: Error exit delayed from previous errors
mv: cannot stat `uudeview': No such file or directory
tar: clamav.tar.gz: Cannot open: No such file or directory
tar: Error is not recoverable: exiting now
tar: Child returned status 2
tar: Error exit delayed from previous errors
mv: cannot stat `clamav': No such file or directory
tar: aps.tar.gz: Cannot open: No such file or directory
tar: Error is not recoverable: exiting now
tar: Child returned status 2
tar: Error exit delayed from previous errors
./setup2: line 873: ispconfig_tmp/php/bin/php: No such file or directory
ERROR: The PHP binary coming with ISPConfig does not work properly on your system! The installation routine stops here!

Any help is greatly appreciated, thank you!

till 28th May 2007 14:07

Did you follow exactly the perefct setup guide for debian etch?

jake 28th May 2007 14:43

Hi,

Thanks for your reply. I followed the setup guide as closely as possible. Because i'm on a vserver i was unable to implement quota (though i installed the package). Furthermore i was unable to install bind9 but installed bind instead.

falko 28th May 2007 17:12

I'm not sure what's causing the error, but I think it's related to you using a vserver. Sometimes they don't behave like dedicated servers. :(

jake 28th May 2007 17:20

Hmm, that's too bad because the previous install had no such problems. Do you know what may be causing the generating of the certificate too take so long when i change the lines in compile_aps/compile?
If i can solve that i guess everything should be working as it should.

till 29th May 2007 09:48

What exactly did you change in the compile_aps/compile script?

jake 29th May 2007 14:08

I changed it according to this:

http://www.howtoforge.com/forums/sho...=.%2FConfigure

(and corrected the typos)

jnsc 29th May 2007 15:45

I had something very similar on a Vserver. A uname -a was telling it was a x86_64 but the vserver was installed as a i386. This was causing SSL compilations errors.

jake 29th May 2007 21:43

What did you do to solve it?
If i just knew what the certifcate generation is taking so long it might help.

jnsc 29th May 2007 22:16

It was a Vserver from vserver.de, after a reboot a uname -a showed the right value i386 instead of x86_64


All times are GMT +2. The time now is 08:50.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.