proftpd 530 Login incorrect?

[pratapsingh]

hi . I was trying to login to localhost using proftpd but it is asking for user name and password . But while installing i did not give any user name and password to proftpd .

I installed proftpd using source code from fftp://ftp.proftpd.org/distrib/proftpd-1.3.2rc4.tar.gz
./configure --sbinddir=/usr/sbin
make
make install

after this i tried to connect to my localhost but it was asking for UName and Password.

[root@localhost ~]# ftp localhost
Connected to localhost.localdomain.
220 FTP Server ready.
500 AUTH not understood
500 AUTH not understood
KERBEROS_V4 rejected as an authentication type
Name (localhost:root): root
331 Password required for root
Password:
530 Login incorrect.
Login failed.
Remote system type is UNIX.
Using binary mode to transfer files.
ftp>

What is the problem did i missed some thing?

proftpd.conf file
>>>
# This is a basic ProFTPD configuration file (rename it to
# 'proftpd.conf' for actual use. It establishes a single server
# and a single anonymous login. It assumes that you have a user/group
# "nobody" and "ftp" for normal operation and anon.

ServerName "ProFTPD Default Installation"
ServerType standalone
DefaultServer on

# Port 21 is the standard FTP port.
Port 21

# Don't use IPv6 support by default.
UseIPv6 off

# Umask 022 is a good standard umask to prevent new dirs and files
# from being group and world writable.
Umask 022

# To prevent DoS attacks, set the maximum number of child processes
# to 30. If you need to allow more than 30 concurrent connections
# at once, simply increase this value. Note that this ONLY works
# in standalone mode, in inetd mode you should use an inetd server
# that allows you to limit maximum number of processes per service
# (such as xinetd).
MaxInstances 30

# Set the user and group under which the server will run.
User nobody
Group nobody

# To cause every FTP user to be "jailed" (chrooted) into their home
# directory, uncomment this line.
DefaultRoot ~

IdentLookups off

ServerIdent on "FTP Server ready."


# Normally, we want files to be overwriteable.
AllowOverwrite on

# Bar use of SITE CHMOD by default
<Limit SITE_CHMOD>
DenyAll
</Limit>

# A basic anonymous configuration, no upload directories. If you do not
# want anonymous users, simply delete this entire <Anonymous> section.
<Anonymous ~ftp>
User ftp
Group ftp

# We want clients to be able to login with "anonymous" as well as "ftp"
UserAlias anonymous ftp

# Limit the maximum number of anonymous logins
MaxClients 10

# We want 'welcome.msg' displayed at login, and '.message' displayed
# in each newly chdired directory.
DisplayLogin welcome.msg
DisplayChdir .message

# Limit WRITE everywhere in the anonymous chroot
<Limit WRITE>
DenyAll
</Limit>
</Anonymous>
<<<<<<<<<:)

[falko]

You must log in with a system user name and his password.

[pratapsingh]

For login to your website through ftp you have to create a user and you must have to specify that usergroup in your /etc/proftpd.conf file. Initially i missed that to specify a usergroup in my proftpd.conf file. After specifying a group there you can login as a user which belongs to that group.

now have look of m,y proftpd.conf file and pay special attention on underlined and bold font .. you need to specify a usergroup .




# This is a basic ProFTPD configuration file (rename it to
# 'proftpd.conf' for actual use. It establishes a single server
# and a single anonymous login. It assumes that you have a user/group
# "nobody" and "ftp" for normal operation and anon.

ServerName "ProFTPD Default Installation"
ServerType standalone
DefaultServer on

# Port 21 is the standard FTP port.
Port 21

# Don't use IPv6 support by default.
UseIPv6 off

# Umask 022 is a good standard umask to prevent new dirs and files
# from being group and world writable.
Umask 022

# To prevent DoS attacks, set the maximum number of child processes
# to 30. If you need to allow more than 30 concurrent connections
# at once, simply increase this value. Note that this ONLY works
# in standalone mode, in inetd mode you should use an inetd server
# that allows you to limit maximum number of processes per service
# (such as xinetd).
MaxInstances 30

# Set the user and group under which the server will run.
User nobody
Group nobody

# Use pam to authenticate (default) and be authoritative
#AuthPAMConfig proftpd
#AuthOrder mod_auth_pam.c* mod_auth_unix.c

#Include /etc/proftpd_ispconfig.conf

# To cause every FTP user to be "jailed" (chrooted) into their home
# directory, uncomment this line.
DefaultRoot ~

<Limit LOGIN>
DenyGroup !ftpusers
</Limit>

IdentLookups off
ServerIdent on "FTP Server ready."


# Normally, we want files to be overwriteable.
AllowOverwrite on

# Bar use of SITE CHMOD by default
<Limit SITE_CHMOD>
DenyAll
</Limit>

# A basic anonymous configuration, no upload directories. If you do not
# want anonymous users, simply delete this entire <Anonymous> section.
<Anonymous ~ftp>
User ftp
Group ftp

# We want clients to be able to login with "anonymous" as well as "ftp"
UserAlias anonymous ftp ftpuser username

# Limit the maximum number of anonymous logins
MaxClients 10

# We want 'welcome.msg' displayed at login, and '.message' displayed
# in each newly chdired directory.
DisplayLogin welcome.msg
DisplayChdir .message

# Limit WRITE everywhere in the anonymous chroot
<Limit WRITE>
DenyAll
</Limit>
</Anonymous>